Outdoor swimming pools in Pimlico
SW1V · Central London · Concrete tanks, heating, covers and landscaped surrounds
Indicative local rate
£1,180 / m²
Area factor
Central London ×1.18
Typical programme
10–25 weeks
Postcode
SW1V
Outdoor Swimming Pools in Pimlico
An outdoor pool is the centrepiece of a garden, and it works best when the pool, the terrace, the planting and the plant room are designed together rather than dropped into a finished landscape.
Pimlico (SW1V) is Thomas Cubitt's planned grid of white stucco terraces between Victoria and the Thames, laid out from the 1820s, with garden squares such as Eccleston, Warwick and St George's Squares and the 1950s Churchill Gardens estate along Grosvenor Road. Most of the original houses were divided into flats long ago, so the typical Pimlico job is a single flat or a few floors of a house rather than a freehold townhouse.
That context shapes how we approach outdoor swimming pools here. Pimlico streets are residents' parking in Westminster with narrow pavements and basement lightwells in front of most houses. Skips, scaffolds and parking suspensions are licensed through the council, and materials are carried through the front door or down the lightwell steps, so we plan small, scheduled deliveries. We survey the property, confirm the consents that apply to SW1V and issue a fixed price against a written scope, so the figure you sign is the figure you pay unless you change the brief.
Our indicative rate for outdoor swimming pools in Central London is around £1,180 per m², reflecting a ×1.18 area factor against our London baseline. Use the instant quotation tool for a figure tailored to your size, specification and start date.
Included in Pimlico
- Site survey, access strategy and ground investigation
- Structural design and planning application where required
- Excavation, spoil removal and reinforced concrete tank
- Waterproofing, tiling, mosaic or liner finish
- Stone coping, non-slip terrace and level detailing
- Filtration, circulation, dosing and plant room construction
- Heat pump or boiler heating, and automatic or slatted covers
- Underwater lighting, controls and automation
How the job runs
Survey and access
Levels, ground conditions, water table, tree constraints and how plant and spoil will physically get in and out.
Design and consents
Pool and structural design, planning where needed, and a build-over or drainage strategy.
Groundworks
Excavation, spoil removal, drainage, service routes and plant room base.
Tank and plant
Reinforced concrete shell, pipework, waterproofing and plant installation.
Finishes
Tiling or liner, coping, terrace, lighting, cover installation and garden reinstatement.
Commissioning
Fill, balance, test, hand over with operating instructions and a maintenance schedule.
Concrete, liner or one-piece shell
A reinforced concrete tank with a tiled or mosaic finish is the premium option: any shape, any depth, decades of life and the best finish. A concrete shell with a reinforced liner costs less, builds faster and gives a 10–15 year liner replacement cycle. One-piece fibreglass shells are quickest of all, but access into a typical London garden usually rules out craning a whole shell in.
The shape follows the garden. A narrow London plot often suits a lap pool along one boundary, leaving usable terrace and planting rather than a token strip of grass around a wide rectangle.
Outdoor swimming pools in Pimlico: common questions
How much does an outdoor pool cost?
Our indicative rate is £1,000 per m² of water surface at standard specification, £1,500 premium and £2,000 luxury, before excavation, plant room and landscaping.
Do I need planning permission for a garden pool?
An outdoor pool within the garden of a house is often permitted development, but conservation areas, listed properties, flats and any enclosure or pool house change that position. We check before designing.
How long does it take?
Typically 12–20 weeks on site, weather and access dependent, plus design and consents beforehand.
Can you build a pool with restricted access?
Usually yes. We use smaller plant, conveyors and manual spoil handling where a machine cannot get through. It adds time and cost, which we set out honestly at quotation stage.